Probably a bit of force will be needed to separate the iPhone's display assembly. If the screen is too damaged to use the suction cup, put some tape over or insert a spudger between the chrome edge and the screen seal to lever up. Remove the 8 following screws : The 5 cruciform screws of 2. Advise for reassembling : The screw near the camera also has a metallic tape holding the it still.
Do not forget to put back this metallic tape before adding the 2. Once the metal part is removed, lever up with the nylon spudger to take off the camera from its spot. Make sure the motherboard is correctly placed before screwing the back of the iPhone. Our goal is to make repairing accessible to all. Our team introduces you Captain Repair, an on-site repair service.
The good point about it is that you can have the repair done at home, at work or at a coffee shop! All rights reserved to SOSav. Why not you? This iPhone repair guide will allow you to replace your iPhone 3G's vibrator. On the shop : Components - iPhone 3GS. Do you have the spare parts to do the repair? Some parts are missing! Insert your SIM eject tool or a paper clip into the hole next to the headphone jack. If you have an iPhone 3GS, refer to picture 2 and use a spudger to disconnect the ribbon cable labeled "7.
Five 2. Two 2. One 2. Use a spudger to gently remove the camera retaining clip, formerly secured by the removed screw and gently pry the camera up and out of its housing in the rear panel. The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.
Use a spudger to gently pry up the end of the logic board closest to the dock connector. If the board won't lift up, double check to make sure all the screws securing the logic board have been removed. These screws are smaller diameter than all the others. Make sure you don't mix them up with the other screws.
On reassembly, only these two screws will fit. Cancel: I did not complete this guide. Badges: After you are done with the replacement and get everything back in place, hard reset the phone as it is the only way to turn it on. I have just successfully replaced the motor, remarkably straightforward though in parts very fiddly , and an excellent guide up to step 6.
Step 2: The screen really comes up with a jerk, I actually pulled off a connector with the initial separation and was very lucky nothing broke. Be very gentle with the initial separation. But all you need to know is that you very carefully flip up the smaller section, whichever colour it may be. At this point, I had access to the motor so I tried my luck. It came out, and the next one went in, with great ease.
You do not need to go any further than step 6 to do this fix. The small section of the motor still covered just slides out with a gentle tug, and my replacement is working fine. After step 6, you can replace the vibration motor by loosening the two screws. You can then tilt the motor from below the motherboard. All the other steps are unnecessary.
Required spare parts. See product Add to cart. Required tools. Standard tool kit. Guide format : Pdf Integrate. See in HD. Maintain the power button on the top for a few seconds and slide to "power off". Step 2 Remove the two screws on both sides of the dock-connector of the iPhone. Step 3 Be careful when opening the iPhone in order not to cut the cables on the top of the motherboard.
Stick the suction cup near the home button and slowly pull the LCD screen and screen. Step 4 The front face of the iPhone is maintained by a few cables. Don't try unpluging it for now. Step 6 With the nylon spudger, lever to disconnect the iPhone' sensitive touch screen.
Step 8 Insert the SIM card eject tool or use a paper clip in the whole located near the jack plug. Push the tool in the whole to have the sim card tray out do no hesitate to use a bit of force. Step 12 Gently remove the small black sticker labeled "Do Not Remove". Step 13 Remove the 8 following screws : The 5 cruciform screws of 2. The two 2. Step 14 With the tweezers, remove the small metal part located on the camera as shown on the picture.
For now, don't remove completely the camera, it is still connected to the motherboard. Step 15 With the nylon spudger, gently lift the bottom of the motherboard.
0コメント